Ok i am going to start by i have already Googled my *** off for the past 5 days,and here i am asking for help because i have tried everything.
First my PS3 model etc.
CECHG 0x05 SEM-001 256MB NAND 40GB 65nm 90nm 10/2007
Had a BMD-002 original BD Board with KES 400a laser.
Firmware: Kmeaw 3.55 (everything is good with that,no troubles freezing etc.)
ok so the laser died or whatever because it would not read anything anymore opened it cleaned, and still nothing laser would just go up and down and thats it disc would not even spin.So i read that you could finally remarry BD drives to other MB's so i was like cool cause i have another BD drive from another PS3 so lets marry it that drive is a KES 410aca with BMD-003 Daughter board,so i went and downgraded with ps3 JIG to 3.41 then again to 2.30 knowing that 256 NAND needs to go that far so everything good so far,then did the remarry process Drive init PASS,install system software went well ok so stayed in service mode or whatever then put in BD movie nothing show up,put in Game nothing show up i was like whatever so i got out of factory mode and then upgraded back to 3.55 and then to kmeaw 3.55 everything good,here is the BS! i know the marry procedure went good because homebrew wont start unless you have a married BD or
even so when i put a game in or movie or music disc the drive sucks the disc in mechanism on the drive working correctly when a game/BRmovie is in the blue ray laser is reading like it should it comes up and everything disc is trying to spin like it spins fast for a bit then slows a bit then full force spin for like 4 sec then slow till it finally stops,with dvd movie the blue ray laser shows up stops then the red laser comes in and the same thing happens and then stops,also over the hole process the top right loading disc icon is going so i know the ps3 reads it and i know the laser is good as the rite lasers show up for different media.
So i did everything i cleaned the laser,changed ribbons,formatted HDD,restore default settings,restore system,everything and its still like that,can someone please let me know whats going on with it if please i mean if the marry pass init,homebrew is loading,lasers working the way they should,disc spinning fast for the most part but then gives up,loading icon on the top right corner the hole time till the disc stops spinning then what else can it be?If i gotten 6 hours of sleep in the past 5 days its a lot i been on my PC and PS3 like a mad man trying to figure this thing out please anyone can help me i truly would appreciate it.
just upgraded to REBUG CFW 3.55.2 and the same thing.
Here is a short video of the issue PS3 remarry process went good but this happens - YouTube
First my PS3 model etc.
CECHG 0x05 SEM-001 256MB NAND 40GB 65nm 90nm 10/2007
Had a BMD-002 original BD Board with KES 400a laser.
Firmware: Kmeaw 3.55 (everything is good with that,no troubles freezing etc.)
ok so the laser died or whatever because it would not read anything anymore opened it cleaned, and still nothing laser would just go up and down and thats it disc would not even spin.So i read that you could finally remarry BD drives to other MB's so i was like cool cause i have another BD drive from another PS3 so lets marry it that drive is a KES 410aca with BMD-003 Daughter board,so i went and downgraded with ps3 JIG to 3.41 then again to 2.30 knowing that 256 NAND needs to go that far so everything good so far,then did the remarry process Drive init PASS,install system software went well ok so stayed in service mode or whatever then put in BD movie nothing show up,put in Game nothing show up i was like whatever so i got out of factory mode and then upgraded back to 3.55 and then to kmeaw 3.55 everything good,here is the BS! i know the marry procedure went good because homebrew wont start unless you have a married BD or
even so when i put a game in or movie or music disc the drive sucks the disc in mechanism on the drive working correctly when a game/BRmovie is in the blue ray laser is reading like it should it comes up and everything disc is trying to spin like it spins fast for a bit then slows a bit then full force spin for like 4 sec then slow till it finally stops,with dvd movie the blue ray laser shows up stops then the red laser comes in and the same thing happens and then stops,also over the hole process the top right loading disc icon is going so i know the ps3 reads it and i know the laser is good as the rite lasers show up for different media.
So i did everything i cleaned the laser,changed ribbons,formatted HDD,restore default settings,restore system,everything and its still like that,can someone please let me know whats going on with it if please i mean if the marry pass init,homebrew is loading,lasers working the way they should,disc spinning fast for the most part but then gives up,loading icon on the top right corner the hole time till the disc stops spinning then what else can it be?If i gotten 6 hours of sleep in the past 5 days its a lot i been on my PC and PS3 like a mad man trying to figure this thing out please anyone can help me i truly would appreciate it.
just upgraded to REBUG CFW 3.55.2 and the same thing.
Here is a short video of the issue PS3 remarry process went good but this happens - YouTube